DuyMinh Software
Bạn có muốn phản ứng với tin nhắn này? Vui lòng đăng ký diễn đàn trong một vài cú nhấp chuột hoặc đăng nhập để tiếp tục.
Tìm kiếm
 
 

Display results as :
 


Rechercher Advanced Search

Liên kết
DuyMinh Software
Minh Hoang HiTech
Music

Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED

Go down

Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED Empty Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED

Bài gửi  duyminh Wed Mar 31, 2010 2:51 pm

Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED Dmscanh20bao20chi20thi2
Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED Dmstanklevelcirminh

Water Level Indicator with alarm - Cảnh báo chỉ thị mức nước bằng đèn LED

This circuit not only indicates the amount of water present in the overhead tank but also gives an alarm when the tank is full.
The circuit uses the widely available CD4066, bilateral switch CMOS IC to indicate the water level through LEDs.
When the water is empty the wires in the tank are open circuited and the 180K resistors pulls the switch low hence opening the switch and LEDs are OFF. As the water starts filling up, first the wire in the tank connected to S1 and the + supply are shorted by water. This closes the switch S1 and turns the LED1 ON. As the water continues to fill the tank, the LEDs2 , 3 and 4 light up gradually.
The no. of levels of indication can be increased to 8 if 2 CD4066 ICs are used in a similar fashion.

When the water is full, the base of the transistor BC148 is pulled high by the water and this saturates the transistor, turning the buzzer ON. The SPST switch has to be opened to turn the buzzer OFF.
Remember to turn the switch ON while pumping water otherwise the buzzer will not sound!


******************

This electronic circuit is a water level Indicator. It is simple and practical measure and know the level of reservoir. The component IC CMOS 4066 used as switcher on any level detector/sensor that connect the negative polarity pin of each LED to ground. Buzzer will be sounded if full level sensor achieved. It's a cool electronic circuit.

Features:

Power Supply 6 - 15 volts
Measuring four different levels
To give voice warning about filling or emptying the reservoir, "exactly according to the delicate"
Very small and components are cheap and available


Parts Lits:

- IC CMOS CD4066
- Transistor BC148
- Resistance 330 Ohm 4x
- Resistance to 180 KOhm 4x
- Four pairs optical multi-color LED
- Small buzzer/bell 6-15 volt


*******************

Đây là mạch không chỉ cho chúng ta biết mức nước ở thời điểm hiện tại mà nó còn cảnh báo cho chúng ta khi mức nước đã đầy bằng hiện thị lên các đèn LED và chuông báo động


Mạch sử dụng IC CMOS CD4066 để đóng cắt và đưa tín hiệu mức nước ra các LED (Trên hình vẽ). Khi mức nước trong thùng không có nước thì điện trở 180K ôm được nối với mức thấp (GND) nên không có đèn LED nào sáng. Khi có mức nước vào thì đầu tiên nó kết nối giữa S1 với nguồn dương thông qua các ion trong nước khi đó đóng khóa S1 tạo cho đèn LED 1 sáng. Cứ như vậy thì các mức 2, 3, ,4 cũng như vậy mức nước đến đâu thì đèn sẽ sáng đến đó.
Riêng khi mức nước đã đầy có thêm 1 chuông cảnh báo là nước trong thùng đã đầy. báo hiệu cho con người là nước đã đầy thùng.
duyminh
duyminh

Tổng số bài gửi : 2887
Points : 5567
Reputation : 83
Join date : 12/09/2008
Age : 42
Đến từ : http://diendan.phamduyminh.com

http://www.phamduyminh.com

Về Đầu Trang Go down

Về Đầu Trang

- Similar topics

 
Permissions in this forum:
Bạn không có quyền trả lời bài viết